Skip to main content
GulpDust
Build adapter

New line

Dust Collection Connectors, Flanges, Clamps, Gates, and Ports

Printed parts that go beyond the adapter. Bolt a dust port onto anything, click one hose from tool to tool, run any hose on a premium extractor, stop your blast gates from jamming, and snap a hose on and off with magnets.

  • PETG
    Not brittle PLA
  • Made in the USA
    Printed to order

The backbone: one hose, every tool

Two parts do the heavy lifting. The bolt-on flange adds a port to any tool, cabinet, or drum. The quick-connect clamp clicks your hose onto that port and pulls off with one hand. Put a flange on every station, then move one hose around the whole shop. Every new station is just one more flange.

GulpDust bolt-on dust port flange, a round plate with four screw holes and a hose spigot

Bolt-On Dust Port Flange

Add a dust port to anything. Bolt it on, snap a hose on, done.

See the details
GulpDust quick-connect hose clamp, a socket with springy fingers and pull wings on a hose spigot

Quick-Connect Hose Clamp

One hose. Every tool. Click it on, click it off.

See the details

Quick wins

Standalone parts that each fix one real headache in the shop.

GulpDust Festool and DeWalt hose adapter, a round tool-side end stepping down to a 2.5 inch hose spigot

Festool and DeWalt Hose Adapter

Run any hose on your Festool or DeWalt extractor.

See the details
GulpDust 4 inch self-cleaning blast gate, two round flanges with a flat blade sliding in the gap between them

Self-Cleaning Blast Gate

A 4 inch blast gate that will not jam with dust.

See the details
GulpDust vacuum hose connector, a ribbed PETG barrel with grip rings and a through bore

Vacuum Hose Connector

Join two hoses, or save a torn one.

See the details
GulpDust universal step adapter, a three-step PETG cone that fits 2-1/2, 1-7/8, and 1-1/4 inch hoses

Universal Step Adapter

One adapter, three hose sizes.

See the details
GulpDust magnetic quick-disconnect dust port, a hose spigot with a magnet-pocket face

Magnetic Quick-Disconnect Port

Snap it on, pull it off. No twist.

See the details
GulpDust 4-inch magnetic dust port, a wide hose spigot with a ring of magnet pockets on the face

4-Inch Magnetic Dust Port

Snap a 4 inch hose on, pull it off. No twist.

See the details

Tool adapters

Built for the dust port on a specific tool, so you pick your tool and hook up your hose. No tape, no guessing.

GulpDust Bosch ROS20VSC sander dust adapter, a reducing tube from the sander port to a 2.5 inch hose

Bosch ROS20VSC Sander Adapter

Bosch ROS20VSC sander to a 2.5 inch hose.

See the details
GulpDust Makita random-orbit sander dust adapter, a reducing tube from the sander cuff to a 36 mm hose

Makita Sander Dust Adapter

Makita BO5041 / BO5030 sander to a dust hose.

See the details
GulpDust Makita circular saw dust adapter, a reducing tube from the saw chip port to a dust hose

Makita Circular Saw Dust Adapter

Makita 18V circular saw to a dust hose.

See the details
GulpDust DeWalt DCW600 trim router dust adapter, a reducing tube from the router port to a 2.5 inch hose

DeWalt DCW600 Router Adapter

DeWalt DCW600 trim router to a 2.5 inch hose.

See the details
GulpDust DeWalt DWE6421 sander dust adapter, a plug end sized for the sander port that flares to a 2.5 inch hose

DeWalt DWE6421 Sander Adapter

DeWalt DWE6421 sander straight to your shop vac.

See the details
GulpDust Makita 5007 circular saw dust hood, a curved shroud that tapes over the chip chute and necks down to a round hose stub

Makita 5007 Circular Saw Dust Hood

Makita 5007 saw dust, straight to your shop vac.

See the details

What Are Dust Collection Connectors?

Dust collection connectors are the parts that join your tools, hoses, and duct into one system. A flange adds a port where there was none. A clamp locks a hose on and off. An adapter meets a tool-brand port. A blast gate opens and closes a duct line. A magnetic port lets you pull a hose off with one hand.

Printed in PETG, these parts fit snug and hold up to shop use. You skip the tape and the mismatched store fittings and build a run that holds together, so your suction stays strong and more of the dust ends up in the bin and less in the air you breathe.

Build the whole run from one shop

From the tool port to the main line, we print every part in PETG. Pick a part type to see sizes and prices.

Also making dust separator lids, floor sweeps, and custom-built adapters.

Connector FAQ

What is the GulpDust backbone system?

It is two parts that work together. A bolt-on flange adds a dust port to any surface, and a quick-connect clamp clicks your hose onto that port. Put a flange on every tool, then move one hose from tool to tool with the clamp.

Are these connectors ready to buy?

The flange, the clamp, the self-cleaning blast gate, the magnetic ports, and every tool adapter are ready to order. The Festool and DeWalt twist-lock adapter is a working prototype: its round fit is set, and we are still tuning the quarter-turn lock on real tools.

What are these connectors made of?

Every part is printed in PETG, a tough plastic that holds up to shop use and static-charged dust better than PLA. Each one is printed to order in the USA.

Can I get these in other sizes?

Yes. Each part lists a default size, and we print most of them to the size you need. Ask when you request one and we match your hose or duct.